Electro-cam PS-6144 Series Uživatelský manuál stáhnout pdf (Strana 18)

2-10 Installation & Wiring

Output Wiring (cont’d)

Figure 10—Wiring for Sinking Transistor Outputs (See Figure 6 for Terminal Block Locations)

Model PS-6144-24-N16-M09

Please Note:

• Outputs are rated at 30 VDC, 50 mA.

• Transistor outputs should not be used to switch inductive devices such as solenoids or

relays.

• Sinking outputs conduct to the negative terminal of TB 11 when “on.”

• The power supply shown in “Load with Built-In Power Supply” does not have to be the same

voltage as the power supply connected to TB 11.

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 111 112

PS-6144 Series 1
Table of Contents 3
Mechanical Cam Switches 5
Programmable Limit Switches 5
PS-6144 Description 6
Basic Terminology 7
PS-6144 Standard Features 7
PS-6144 Optional Features 8
General Mounting & Wiring 9
PGM:1 RPM:1500 10
MENU< POS: 180 10
2-3 Installation & Wiring 11
2-4 Installation & Wiring 12
Controller Input Wiring 13
2-6 Installation & Wiring 14
2-7 Installation & Wiring 15
Output Wiring 16
Output Wiring (cont’d) 17
Keypad Wiring 20
DIP Switch Configurations 21
Communications Wiring 23
Resolver Installation 24
Resolver Dimensions 25
Resolver Cables 26
Output Transistor Replacement 28
Menu Tree 30
Initial Programming 31
OFFSET 3-16 31
Analog Module Numbe 32
Analog High RPM 32
Analog Offset 32
Number of Analog Output 33
Communications 34
Channel Copy 34
Communications (Cont’d) 35
Default Program 35
LEVEL: OPERATOR 36
PASSWORD: 1234 36
Password Number 36
View Program 37
--- --- --- Program 37
Enable Codes (cont’d) 37
GROUP POSITION 38
DISPLAY: EACH< 38
Machine Speed 39
Active Program 39
Keyboard Quantity 40
Input Status 40
Motion ANDing 42
Memory Tests 42
Motion detection leve 43
High RPM setpoint 43
Low RPM setpoint 43
Value for this Group 44
3-17 Programming 45
Output Enable ANDing 46
Output Groups 46
Output Groups (Cont’d) 47
Output Status 47
Password 48
Output Status (Cont’d) 48
Password (Cont’d) 49
Per Channel Enable 49
Program Copy 49
Pulse Copy 50
Program Select Mode 50
Pulse Copy (cont’d) 51
Rate Setup 52
SCALE 53
FACTOR: 360< 53
Program to view or modify 54
Setpoints (Cont’d) 55
CH:1 EDG 55
Output Channel 56
Speed Compensation (cont’d) 57
Speed Comp Mode 57
Timed Outputs 58
Toggle RPM 58
4-1 Speed Compensation 59
Standard Speed Comp 60
Standard Speed Comp (Cont’d) 61
Leading Trailing Speed Comp 62
4-5 Speed Compensation 63
Speed Comp Guidelines 64
Negative Speed Compensation 64
Mode 1 Operation 67
Mode 0 Operation 67
Mode 2 Operation 68
Mode 1 Operation (Cont’d) 68
Mode 2 Operation (Cont’d) 69
Mode 3 Operation 69
Mode 4 Operation 70
Mode 3 Operation (Cont’d) 70
Mode 4 Operation (Cont’d) 71
Mode 5 Operation 71
Mode 5 Operation (cont’d) 72
6-1 Communications 73
PLuSNET II Program (cont’d) 74
6-3 Communications 75
Serial Commands 76
Serial Commands (cont’d) 77
Output group offset value 80
Shaft position offset 80
Checksum 84
Error Codes 84
6-13 Communications 85
40279 Offset Mapping 86
Motion Detection 86
40289 Analog High RPM 86
Quick Reference 86
40310 Analog Quantity 87
Discrete I/O 88
Registers 89
Registers (Cont'd) 90
40280 Group Index 91
40281 Group Offset 91
40288 Analog Offset 92
40308 Shaft Position 93
40309 Shaft Offset 93
Bit 5: Motion detection 95
Special Functions 98
Controller Diagnostics 99
Keypad Diagnostics 100
ERROR: RESOLVER 101
NOT CONNECTED! 101
General Troubleshooting 102
7-5 Troubleshooting 103
Fuse Part Numbers 104
PS-6144 Controller Specs 105
A-2 Appendix 106
Resolver Specifications 107
Factory Defaults 107
A-4 Appendix 108
Access Codes, Entering 3-20 109
Analog Output 3-4 109
Group Position Display 3-10 109
Offset, Analog Output 3-4 110
I-3 Index 111
PRINTED IN U.S.A 256 10/01 112

Komentáře k této Příručce

Žádné komentáře

Electro-cam PS-6144 Series Uživatelský manuál Strana 18

Komentáře k této Příručce

Související produkty a manuály pro Směrovače Electro-cam PS-6144 Series